FAQ RoHS/Report ISO order inquiry Profile HOME ENGLISH Chinese Simplified Chinese Traditional BENNIC

X-OVER NETWORK Inductors Non-Polar Capacitors *Co-Axial Speaker Use *X-OVER Network Use Reliable Film Capacitors Non-Polar Capacitors *Co-Axial Speaker Use *X-OVER Network Use Uni-Polar Aluminium Electrolytic Capacitors For Speaker *Binding Post *Terminals CEMENT TYPE WIRE WOUND RESISTORS L-PAD Attenuators


BENNIC \ NON-POLAR CAPACITORS \ BENNIC ACOUSTIC CAPACITORS \
ELECTROLYTIC CAPACITORS >> P03 | B03 | B04 | B05 | B06 | B10 | B12 | B15 | N04 | N06 | N10
METALLIZED POLYESTER FILM CAPACITORS >> BMET (PEMT) | BMEF (PEMF) | BMED (PEMD)
METALLIZED POLYPROPYLENE FILM CAPACITORS >> BMPT (PPMT) | XPP | FPP | UPP

BENNIC BI-POLAR ELECTROLYTIC CAPACITORS
P03A & P03R SERIES

1) FIGURE : P03A (AXIAL) P03R (RADIAL)
LEAD WIRE DIA AT mm, TOL. ± 0.05 mm (AXIAL DIA 12 øLEAD DIA MAYBE 0.6 mm)
CASE DIA 5 ø 6 ø 8 ø 10 ø 12 ø 13 ø 16 ø 18 ø 20 ø 22 ø 25 ø
AXIAL - 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8
RADIAL 0.5 0.5 0.6 0.6 - 0.6 0.8 0.8 0.8 0.8 0.8

LEAD LENGTH : AXIAL min. 40mm., RADIAL min. 20 mm & 25 mm
RADIAL LEAD PITCH AT mm TOL. ± 0.5 mm
CASE DIA
5 ø
6 ø
8 ø
10 ø
13 ø
16 ø
18 ø
20 ø
22 ø
25 ø
LEAD PITCH
2.0
2.5
3.5
5.0
5.0
7.5
7.5
8.0
10.0
12.5

2) TOL. RANGE: ± 20% (M), or ± 10% (K), or ± 5% (J) @1KHZ
3) LEAKAGE: Max 0.04 CV +3 μA AFTER CHARGE 5 MINUTES
4) TEMP. RANGE 40 ºC TO +85 ºC ( UPON REQUESTED - 40 ºC TO +105 ºC )
5) SURGE VOLT 63V-FOR 50WV., 125V FOR 100WV
6) LIFE TEST : FOLLOWING CHARACTERISTICS SHALL BE SATISFIED WHEN RETURN TO 25 ºC , AFTER RATED VOLTAGE APPLIED FOR 1,000 HOURS AT 85 ºC :
(a) CAPACITANCE CHANGE : WITHIN ± 20% OF INITIAL VALUE
(b) DISSIPATION FACTOR : WITHIN 200% OF INITIAL VALUE
(c) LEAKAGE CURRENT : WITHIN INITIAL VALUE
7) SHELF LIFE : FOLLOWING CHARACTERISTICS SHALL BE SATISFIED WHEN RETURN TO 25 ºC , AFTER WITHOUT RATED VOLTAGE APPLIED 1000HRS AT 85 ºC :
(a) CAPACITANCE CHANGE : WITHIN ± 20% OF INITIAL MEASURED VALUE
(b) DISSIPATION FACTOR : WITHIN 200% OF INITIAL MEASURED VALUE
(c) LEAKAGE CURRENT : WITHIN INITIAL MEASURED VALUE
8) MAX. D.F 3% @1KHZ (FOR EXCEED 3.9 μF), 12 % @20KHZ (FOR UNDER 18 μF)
4 % @1KHZ (FOR UNDER 3.3 μF)., 20 % @20KHZ (FOR EXCEED 22 μF)
9) MARKING BENNIC
P03 P03
xxx MFD xxx WV
10) Sleeve Standard color : Black, Dark blue

11) CASE SIZE (DxL) TABLE (FOR STANDARD VALUE) - AT mm, TOL. ± 1 mm
SERIES P03A (AXIAL) P03R (RADIAL)
MFD \ WV 50WV 100WV 50WV 100WV
1.0 10 x 26 12 x 26 10 x 15 13 x 21
1.5 10 x 26 12 x 31 10 x 20 13 x 21
2.2 12 x 26 13 x 31 13 x 21 13 x 26
2.7 12 x 31 16 x 34 13 x 26 16 x 27
3.3 12 x 31 16 x 34 13 x 26 16 x 27
3.9 13 x 31 16 x 34 13 x 26 16 x 27
4.7 16 x 34 16 x 42 16 x 27 16 x 36
5.6 16 x 34 16 x 42 16 x 27 16 x 36
6.8 16 x 34 18 x 42 16 x 27 18 x 36
7.5 16 x 42 18 x 42 16 x 36 18 x 36
9.2 16 x 42 22 x 44 16 x 36 22 x 37
10 16 x 42 22 x 44 16 x 36 22 x 37
12 18 x 42 22 x 50 18 x 36 22 x 42
15 18 x 42 25 x 52 18 x 36 22 x 44
18 22 x 44 25 x 52 22 x 37 22 x 44
22 22 x 44 25 x 56 22 x 37 25 x 48
27 25 x 52 25 x 60 22 x 44 25 x 53
33 25 x 52 N/A 22 x 44 N/A
47 25 x 60 N/A 25 x 53 N/A

** ANY SPECIAL VALUE ARE ACCEPTABLE, ITS SIZE TO BE PROVIDED UPON REQUESTED
** SIZE MAYBE CHANGED W/O NOTICE., SPECIAL SIZE IS ACCEPTABLE

** Case size table are our standard series / size / value . Any special requested upon discussion.

** Here we only accept to use the following sleeve color for the full compliance with the
    Sony SS-00259 (the sleeve must be use PET material):Black, Dark blue
    or all other color will be accepted only based M.O.Q. 500K per order for each item,
    otherwise unless you could accept non-compliance Sony SS-00259
    (Still compliance with RoHS required).



E-Mail:mail@bennic.com.tw