FAQ RoHS/Report ISO order inquiry Profile HOME ENGLISH Chinese Simplified Chinese Traditional BENNIC

X-OVER NETWORK Inductors Non-Polar Capacitors *Co-Axial Speaker Use *X-OVER Network Use Reliable Film Capacitors Non-Polar Capacitors *Co-Axial Speaker Use *X-OVER Network Use Uni-Polar Aluminium Electrolytic Capacitors For Speaker *Binding Post *Terminals CEMENT TYPE WIRE WOUND RESISTORS L-PAD Attenuators


BENNIC \ NON-POLAR CAPACITORS \ BENNIC ACOUSTIC CAPACITORS \
ELECTROLYTIC CAPACITORS >> P03 | B03 | B04 | B05 | B06 | B10 | B12 | B15 | N04 | N06 | N10
METALLIZED POLYESTER FILM CAPACITORS >> BMET (PEMT) | BMEF (PEMF) | BMED (PEMD)
METALLIZED POLYPROPYLENE FILM CAPACITORS >> BMPT (PPMT) | XPP | FPP | UPP

"BENNIC" BI-POLAR ELECTROLYTIC CAPACITORS
B03A & B03R SERIES

1) FIGURE : B03A (AXIAL)

B03R (RADIAL)


LEAD WIRE DIA AT mm, TOL. ± 0.05 mm (AXIAL DIA 12 øLEAD DIA MAYBE 0.6 mm)
CASE DIA 5 ø 6 ø 8 ø 10 ø 12 ø 13 ø 16 ø 18 ø 20 ø 22 ø 25 ø
AXIAL - 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8
RADIAL 0.5 0.5 0.6 0.6 - 0.6 0.8 0.8 0.8 0.8 0.8

LEAD LENGTH : AXIAL min. 40mm., RADIAL min. 20 mm & 25 mm
RADIAL LEAD PITCH AT mm TOL. ± 0.5 mm
CASE DIA 5 ø 6 ø 8 ø 10 ø 13 ø 16 ø 18 ø 20 ø 22 ø 25 ø
LEAD PITCH 2.0 2.5 3.5 5.0 5.0 7.5 7.5 8.0 10.0 12.5

2) TOL. RANGE : ± 10% (K), or ± 5% (J) , or ± 2.5% (H) @1KHZ
3) LEAKAGE : Max 0.04 CV +3 μA AFTER CHARGE 5 MINUTES
4) TEMP. RANGE : - 40 ºC TO +85 ºC ( UPON REQUESTED - 40 ºC TO +105 ºC )
5) SURGE VOLT : 125V FOR 100WV
6) LIFE TEST : FOLLOWING CHARACTERISTICS SHALL BE SATISFIED WHEN RETURN TO 25 ºC , AFTER RATED VOLTAGE APPLIED FOR 1,000 HOURS AT 85 ºC :
(a) CAPACITANCE CHANGE : WITHIN ± 20% OF INITIAL VALUE
(b) DISSIPATION FACTOR : WITHIN 200% OF INITIAL VALUE
(c) LEAKAGE CURRENT : WITHIN INITIAL VALUE
7) SHELF LIFE : FOLLOWING CHARACTERISTICS SHALL BE SATISFIED WHEN RETURN TO 25 ºC , AFTER WITHOUT RATED VOLTAGE APPLIED 1000HRS AT 85 ºC :
(a) CAPACITANCE CHANGE : WITHIN ± 20% OF INITIAL MEASURED VALUE
(b) DISSIPATION FACTOR : WITHIN 200% OF INITIAL MEASURED VALUE
(c) LEAKAGE CURRENT : WITHIN INITIAL MEASURED VALUE
8) MAX. D.F. : Max 12% @10KHZ (UNDER 47 μF ) , Max 20% @10KHZ ( EXCEED 47 μF )
Max 3% @1KHZ ( When @1KHZ Capacitance under 6.8μF , Max D.F. May possibly surpass the above value.)
9) MARKING : BENNIC
B03 B03
xxx MFD xxx WV
10) Sleeve Standard color : Yellow

11) CASE SIZE (DxL) TABLE (FOR STANDARD VALUE) - AT mm, TOL. ± 1 mm
MFD \ SERIES B03A(AXIAL)100WV B03R(RADIAL)100WV
1.0 10 x 18 10 x 15
1.5 10 x 18 10 x 15
2.2 10 x 18 10 x 15
2.7 12 x 26 10 x 20
3.3 12 x 26 10 x 20
3.9 12 x 26 13 x 21
4.7 12 x 31 13 x 26
5.6 12 x 31 13 x 26
6.8 12 x 31 13 x 26
7.5 12 x 31 13 x 26
8.2 12 x 31 13 x 26
10 16 x 34 16 x 27
12 16 x 34 16 x 27
15 16 x 34 16 x 27
18 16 x 34 16 x 27
22 16 x 42 16 x 36
27 16 x 42 16 x 36
33 16 x 42 16 x 36
47 18 x 42 18 x 36
56 18 x 42 18 x 36
68 22 x 44 22 x 37
75 22 x 44 22 x 37
82 22 x 44 22 x 37
100 22 x 44 22 x 37
120 25 x 52 25 x 43
150 25 x 52 25 x 43

  12) MAXIMUM RIPPLE CURRENT (mA) (at 1KHz , 85 ºC)
MFD \ SERIES B03A(AXIAL)100WV B03R(RADIAL)100WV
1.0 89 103
1.5 109 126
2.2 133 152
2.7 188 185
3.3 208 204
3.9 235 269
4.7 271 317
5.6 296 346
6.8 326 381
7.5 343 400
8.2 358 418
10 478 538
12 524 589
15 586 659
18 642 722
22 789 877
27 874 972
33 966 1075
47 1223 1386
56 1335 1513
68 1683 1927
75 1767 2024
82 1848 2116
100 2041 2337
120 2562 2972
150 2864 3323


** ANY SPECIAL VALUE ARE ACCEPTABLE, ITS SIZE TO BE PROVIDED UPON REQUESTED
** SIZE MAYBE CHANGED W/O NOTICE., SPECIAL SIZE IS ACCEPTABLE

** Case size table are our standard series / size / value . Any special requested upon discussion.

** Here we only accept to use the following sleeve color for the full compliance with the
    Sony SS-00259 (the sleeve must be use PET material):Black, Dark blue
    or all other color will be accepted only based M.O.Q. 500K per order for each item,
    otherwise unless you could accept non-compliance Sony SS-00259
    (Still compliance with RoHS required).



E-Mail:mail@bennic.com.tw